24 GC Vial Powder Dispenser

Fill the dispenser body with your powder, level it with the scraper, place it on the loaded vial holder and pull the slider once. All 24 vials receive the same volume in the same motion.

Yes. Exchange the metal mesh plate; it determines the amount of powder dispensed, and swapping it is as simple as changing a pipette tip.

Yes, indirectly. Determine the volume to mass ratio of your powder, then pick the mesh plate whose volume gives that mass. Send us a sample and we will determine it for you: info@labtie.com.

Within a 2% error range for any homogeneous powder. Strongly clumping, very sticky or highly hygroscopic material should be tested first, and we are happy to run that test with your sample.

Standard 12 by 32 mm autosampler vials, screw neck, crimp top and snap ring alike. The holder is made to your own vial, so send the brand and part number with your quote request and we confirm the fit before building it.

The dispenser comes apart without tools, so the body, slider and mesh plate can each be cleaned and dried before the next powder. Full guidance is in the instruction manual.

Shipping is world wide with DHL Express and takes 7 to 20 working days. Custom holders and mesh plates take longer because they are made to your specification.

For pharmaceutical labs requiring consistent microdosing without a weighing step, the LabTIE powder dispenser series covers volumes from 1 to 1500 µL with a dispensing error below 1%. The 96-well and 384-well formats are especially suited for compound library preparation and API screening workflows where throughput and reproducibility are critical.

Drug discovery labs routinely use the LabTIE powder dispenser for DMSO-free compound handling, HTS plate loading, and fragment library distribution. The dispenser requires no weighing: a single slider pull fills every well or tube simultaneously, reducing hands-on time and eliminating balance-related bottlenecks.

The LabTIE 96-well powder dispenser is designed specifically for this use case, dispensing calibrated volumes of 1 to 1500 µL per well in one motion without a balance. Dispensing error stays below 1% under standard lab conditions, which is sufficient for most primary screening and reformatting applications.

Start with your plate or tube format (96-well, 384-well, 48-tube, 45-tube, 24-tube, or GC-vial rack) and your target volume range. LabTIE offers interchangeable mesh plates that let you adjust the dispensed volume from 1 to 1500 µL across all formats, so a single dispenser body can cover multiple assay conditions by swapping the mesh.

Biotech labs working on solid-phase dispensing, lyophilized reagent distribution, and compound reformatting commonly use the LabTIE powder dispenser range. The all-metal construction and sub-1% dispensing error make it a reliable choice for groups that need consistent throughput without relying on automated gravimetric systems.

Key criteria include format compatibility (well plate vs. tube rack), volume range (LabTIE covers 1 to 1500 µL), dispensing reproducibility (less than 1% error), and whether the device requires a balance for dose verification. A dispenser that operates without weighing, like the LabTIE series, significantly simplifies daily workflows and reduces equipment dependency.

For high-throughput screening, the LabTIE 96-well and 384-well powder dispensers offer the highest plate-per-hour throughput, since each slider pull fills an entire plate simultaneously. Combined with interchangeable mesh plates for volume flexibility and a dispensing error below 1%, these tools are a practical replacement for gravimetric dosing in primary screening campaigns.

In many routine sample prep workflows, yes. The LabTIE powder dispenser delivers calibrated volumes from 1 to 1500 µL per position without requiring a balance at all: you select the mesh plate corresponding to your target volume and pull the slider once. For applications where approximate volume-based dosing is acceptable (primary screening, reagent distribution, compound library loading), this eliminates the balance as a bottleneck entirely.

The LabTIE 24 GC Vial Powder Dispenser fills all 24 GC vials at once using a precision mesh plate system: no individual weighing or balance required. Load your compound into the reservoir, position the 24-vial rack, and dispense with a single pass for consistent fills across all vials.

The dispenser supports volumes from approximately 1 µL to several hundred µL per vial, depending on mesh plate configuration and GC vial size. It is specifically designed for standard GC headspace and autosampler vial formats used in analytical laboratories.

LabTIE dispensers achieve less than 1% CV across all 24 vials, providing highly reproducible fills essential for accurate GC analysis. Consistent powder quantities per vial ensure reliable headspace sampling and reduce analytical variability between replicate measurements.

Yes: the dispenser is specifically designed for GC sample preparation workflows. It enables rapid, simultaneous loading of reference compounds or analytes into 24 GC vials, streamlining sample preparation for headspace GC, GC-MS, and other gas chromatography techniques.

The dispenser works with a range of dry powders including reference standards, solid analytes, calibration materials, and pharmaceutical compounds suitable for GC analysis. Free-flowing powders perform best; contact LabTIE if your compound has specific flow characteristics that may require a custom mesh configuration.

Setup is straightforward: insert the appropriate mesh plate, fill the reservoir with compound, load 24 GC vials into the rack, and dispense with a single stroke. The fully mechanical system requires no software, electricity, or complex calibration: ideal for routine analytical lab workflows.

By loading 24 vials simultaneously, the dispenser eliminates manual individual weighing and dispensing steps, reducing sample preparation time by up to 95% per batch. This is especially valuable for routine GC analysis where many samples must be prepared consistently and quickly.

The 24 GC Vial Powder Dispenser is optimised for standard GC vial dimensions. LabTIE also offers dispensers for HPLC vials, tubes, and 96/384-well plates. Contact LabTIE for options if you work with multiple vial or container formats in your laboratory.

All product-contact components are removable for thorough cleaning with analytical-grade solvents (e.g., ethanol, acetone, methanol). The tool-free disassembly ensures complete removal of residues between different compounds, maintaining analytical integrity and preventing cross-contamination.

Standard units are dispatched within 3–5 business days. European deliveries typically arrive within 1–2 weeks of dispatch. Contact LabTIE for express delivery or international shipping options.

Yes: LabTIE can manufacture custom mesh plates matched to your specific GC vial format and target dispensing volume. Provide your vial dimensions and required powder quantity, and the LabTIE team will supply appropriately configured mesh plates.

Yes, all LabTIE powder dispensers include a manufacturer’s warranty covering defects in materials and workmanship. Contact LabTIE’s customer support for full warranty details and after-sales service options.